A Barrett company - serving Santa Clarita, CA

KraftMaid Windows & Doors in Santa Clarita, CA

Windows & doorsWindows & doors
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

KraftMaid Windows & Doors: The Santa Clarita Owner’s Guide

We install and repair KraftMaid windows and doors in Santa Clarita, and the honest answer on cost is this: full window replacement runs $4,500 – $15,000 for a typical house, while impact-rated units climb to $8,000 – $25,000. Door and hardware-level repairs usually land far below that. Most owners call us after a door starts dragging on the strike plate, a sash won’t stay up, or a hinge pulls loose from the jamb, and the part underneath has finally given out.

Professional construction worker applying sealant to window frame in Santa Clarita, CA

Call (833) 762-8116

That sequence is common in Santa Clarita. The heat and dry air work on seals, hinges and weatherstripping long before the glass or frame shows a problem, so the failure usually shows up as a small annoyance that grows into a draft, a sticking door, or a crack you can see daylight through. Getting the right part matched to your KraftMaid unit is the whole job. Everything else is labor.

Key Takeaways

  • Window replacement in Santa Clarita: $4,500 – $15,000; impact windows: $8,000 – $25,000.
  • Most KraftMaid failures are hardware, seals and weatherstripping, not glass.
  • We’re an independent service provider and not affiliated with KraftMaid.
  • Every eligible job gets permits pulled and inspections signed.
  • 90-Day Done Right Promise in writing on every contract.

Which KraftMaid Models This Applies To

KraftMaid builds windows and doors in a few lines, and the part you need depends entirely on which line and which era your unit came from. The identification happens on a manufacturer’s label, usually on the top or side of the sash, inside the jamb, or on the door edge behind the hinge. That label carries the series and the unit size. If the label is gone, we measure the rough opening and the sash itself and match from there.

Here’s the compatibility gotcha most homeowners miss: KraftMaid has changed hinge styles and sash balance systems across production runs, and a hinge that looks identical to the eye can be a different screw pattern and a different pivot geometry. Order the “same” part off a photo and you’ll often get something that fits one side of the door and binds on the other. The series number on the label is what settles it. Bring us the label, or let us read it.

OEM versus aftermarket for KraftMaid specifically: OEM gets you the exact fit with no measuring guesswork. A quality aftermarket equivalent can work well for weatherstripping, sweep seals and sash balances, and costs less. For hinge sets on heavier doors, OEM is usually the smarter call because the geometry has to match. We’ll tell you which route makes sense for your unit before you spend anything.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your KraftMaid Windows & Doors Is Failing

Five symptoms we see most often in Santa Clarita homes, and what’s actually behind each one:

  • The door drags or won’t latch. Usually a worn hinge or a jamb that has shifted with seasonal movement. When the top hinge loosens, the door sags and the strike no longer lines up, and forcing it wears the latch out too.
  • You feel air around the frame. Failed weatherstripping or a sweep seal that has dried and cracked. In our climate the seal gives out from heat and low humidity before the door itself does.
  • The sash won’t stay open. A spent sash balance or spiral balance. Once the tension goes, the window drops, and continuing to use it wears the track and the pivot shoes.
  • Water stains or soft wood at the sill. A failed sill seal or flashing detail letting moisture in. Left alone, this moves into framing, and the repair grows well past a part swap.
  • Condensation between the panes. A broken seal in the insulated glass unit, not a hardware problem. The glass assembly itself has to be replaced, which is a different job and a different price.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

In Santa Clarita, window replacement runs $4,500 – $15,000 for a typical home, and impact window installation runs $8,000 – $25,000. Those ranges cover the units, removal and disposal of the old ones, and installation. What pushes you toward the top: more openings, larger or custom sizes, impact-rated glass, and any rot or framing repair found once the old unit comes out. What keeps you at the bottom: a straightforward swap on standard sizes with sound framing.

On the parts side, we quote parts plus labor as separate line items so you can see what the hardware costs and what the install costs. You’ll get a written estimate, not a phone number that turns into a different bill at the door. Every eligible job gets permits pulled and inspections signed, and the work carries our 90-Day Done Right Promise in writing. If something’s not right, one call brings us back.

DIY or Call Us?

Some of this is safe to check yourself. You can read the label on the sash or door edge, measure the opening, tighten a visibly loose hinge screw, clean and lubricate a track, and note where the air or water is coming in. That information helps us match the right part on the first visit.

Where DIY goes wrong: replacing a sash balance under tension, reseating hinges on a heavy door so the geometry lines up, and pulling a window unit to deal with hidden rot or flashing. A window unit is heavy, and a unit that comes out of the opening wrong can fall. That’s a two-person job with the right blocking, not a Saturday project on a ladder. If the seal between the glass panes has failed, there’s nothing to fix in place; the glass assembly gets replaced. Call us at (833) 762-8116 and we’ll tell you honestly whether it’s a part, a repair, or a replacement.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (833) 762-8116
Local Service Coverage

Request a Free Estimate in Santa Clarita

Tell us what you need - Barrett & Sons Construction Santa Clarita responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch