Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Windows & Doors: The Santa Clarita Owner’s Guide
CGI is a Canadian window and door manufacturer, and the company built its line around one idea: components match. Their flagship CGI Sentinel line and the older aluminum series that still dominate plenty of homes from Canyon Country to Castaic share a set of standard frame depths, hinge positions, and hardware guide dimensions. That means a window or patio door unit in a Santa Clarita home usually has a correct replacement available, and the part can be matched to the existing opening and to the unit’s glazing system rather than made to work by trimming.

What sets the price and the schedule is what you’re replacing and how the opening was built into the wall. Here in Santa Clarita, most CGI windows and doors we see need attention for the wall finish and the flashing around the opening, not the frame itself. Those homes are typically stucco over dimensional lumber, with a mild inland climate that swings hard between dry summer heat and cool winter nights. That swing works the seals, the caulk joints, and the door hardware year after year.
Full window replacement in Santa Clarita runs $4,500 to $15,000, and impact-rated window installation runs $8,000 to $25,000. If a door is at the end of its life, we quote it separately and install on a schedule, usually within a couple of weeks, not the same day. Nobody plans a window swap overnight, and we won’t pretend otherwise.
We’re an independent contractor and we’re not affiliated with CGI. What we do is source the right unit or hardware for your existing CGI opening, install it correctly, and stand behind the work with our written 90-Day Done Right Promise. Every eligible job includes permits pulled and inspections signed by the city or county.
How Santa Clarita homeowners usually find out something failed
Three things show up most often. A window that no longer closes flush, leaving a thin line of daylight along the frame. A patio door that grinds, drags, or needs a shoulder to seat. Water staining at the interior sill after the first rain, long before anyone notices a draft. Almost everyone calls after that first storm water mark, not before.
Which CGI Models This Applies To
Getting the right part starts with identifying the unit, and CGI makes this easier than most because the manufacturer stamps its windows and doors. Look for the certification label or AAMA sticker on the frame, usually on the jamb or the head of the unit. The code on that label carries the series and glazing details. It often fades or gets painted over in older homes, so a photo and a tape measure are your next best tools.
Write down four measurements: the visible glass width and height, the overall frame width and height, and the frame depth. Take a photo of the hinge side of a door and both the interior and exterior of a window. Those details are usually enough for us to identify the unit and pull the matching part. It’s faster and cheaper than guessing and returning between Santa Clarita and a supplier.
On the aftermarket side, there’s a real decision to make. CGI’s own hardware is the safest match when it’s still available for your series, but the company’s product line has shifted since the 1990s and not every vintage part is still in production. A quality aftermarket window operator, hinge set, or door roller can be a solid substitute if the dimensions and travel match the original. That’s the part that matters: the guide dimensions and travel, not the brand printed on the part. We’ll tell you plainly when an aftermarket equivalent will work and when it won’t.
One common compatibility snag: the hinge position on some CGI series differs from the generic hinge sets sold at home centers, and a set that fits the opening may still not align with the original screw pattern. Installing one anyway means drilling new holes and losing the factory anchors, which weakens the frame’s attachment over time. That’s the kind of thing that shows up two winters later.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Windows & Doors Is Failing
Here’s what we actually see across Santa Clarita homes, and what’s usually behind it.

- Daylight around the edge of a closed window. The sash has been pulled out of square, usually because the frame settled or the seal has compressed unevenly. Over months, that gap lets hot afternoon air in and drives up the interior temperature on the side of the house facing the sun.
- A patio door that grinds or drags on the sill. Either the roller is worn flat, the track has grit, or the door has sagged at the hinge side. Grinding is the sound of failing hardware, and it gets worse faster in a home where the door gets daily use.
- A door that won’t seat flush in the closed position. The latch or the hinge set is tired, or the frame is out of square. A door that won’t fully seat leaves a gap you can feel as a draft and that water will find.
- Water staining or soft wood at the interior sill. This is the one to take seriously. It usually points to failed caulk and flashing at the exterior opening, a couple of seasons before it finds its way to the drywall or the subfloor.
- Condensation between the panes. The sealed unit has failed and the glazing is no longer doing its insulating job. Replacing the sash or glazing unit restores the insulation, and the condensation stops.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Santa Clarita window and door pricing breaks down by what’s actually being replaced. Window replacement ranges $4,500 to $15,000 for a typical project, and impact-rated window installation in this market runs $8,000 to $25,000. A single window sash or an incomplete set of hardware sits well under that. Where a door or a standard window is involved, we quote the unit, the labor, and any permitting as separate line items so you can see exactly where the money goes.
Here’s the honest breakdown behind the range:
- Window replacement, $4,500 to $15,000. Driven by unit count, glazing type, and how many openings need flashing and stucco work. A single cracked sash is far cheaper than a full set.
- Impact window installation, $8,000 to $25,000. Impact-rated glass and the hardware that carries it are heavier and more expensive, so it runs higher.
- Door hardware or sash repair. Smaller part-and-labor jobs, priced at the visit, usually $40 to $200 for a simple hardware swap or adjustment.
What’s included: written scope, allowances for the glazing or hardware, and a line-item quote. Any price change is issued as a written change order before work proceeds. The work itself is backed by our written 90-Day Done Right Promise. Our published offers apply here too: $40 off any repair over $200, a free second opinion on any written estimate, a permanent 10% Senior & Veteran discount, and no trip charge inside the county.
DIY or Call Us?
Some of this you can safely check. You can measure the opening, photograph the label, wipe grit off a stubborn track, and tighten a visible screw or two. That’s useful information to us and it costs nothing.
The part most people shouldn’t tackle alone is the hardware swap on a fully loaded sash or a door unit. A sliding glass door or a heavy sash carries real weight, and getting it off the track safely and back on without injury or bending the frame is a two-person job. Doing it wrong, even once, can misalign the frame or crack the glass. If you’re not sure, call us at (833) 762-8116. We’ll tell you honestly whether you’re looking at a quick hardware swap or a full replacement.
FAQs
A well-installed CGI window or door typically holds up 20 to 25 years in this climate. The frame components often outlast the seals and caulk joints, and those usually need attention first. Heat and the dry-to-cool swing inland tend to age the exterior caulk and the door hardware faster than anything inside the unit.
Often, yes. A worn roller, hinge set, latch, or a single failed glazing unit can usually be repaired or swapped without replacing the whole window or door. If the frame itself is cracked or badly out of square, replacement is usually the better call. We’ll tell you which one you’re looking at.
A small hardware or sash swap usually takes a couple of hours. A full window or door replacement is a scheduled job, typically a day or two depending on the unit and how much stucco or framing is involved. We don’t do replacements the same day, and we’ll give you a real date, not a promise.
We start from your label or your measurements and photos, identify the series, and check whether original CGI hardware is still available. If it isn’t, we match a quality aftermarket equivalent that meets the original dimensions and travel. Then we confirm it will seat in your frame before we order it. We’ll quote a window and impact-window project honestly and let you decide. Our published offers apply, including the free second opinion on any written estimate.
We also service KraftMaid, Cambria, and Silestone across the rest of the home.
If you’ve got a CGI window that won’t close, a door that won’t seat, or a spotted glazing unit that’s telling you it’s ready to be dealt with, call Barrett & Sons Construction Santa Clarita at (833) 762-8116 for a free estimate. A live person answers, and every estimate comes in writing.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.