Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Driveway & Pavers: The Santa Clarita Owner’s Guide
Installing CGI-compatible driveway and paver work in Santa Clarita typically runs $7,000 – $18,000 for a paver driveway and $3,500 – $11,000 for a paver patio, depending on square footage, base prep, and drainage. We can usually walk a driveway job within a few days of your call, and we’ll give you a written line-item quote before any material gets ordered. Owners here usually find out something is wrong the same way: a paver pops loose after a hot week, a hairline crack keeps spreading across a slab, or water pools against the garage door after a hard rain because the base settled. Our technicians have up to 28 years of experience, and every eligible job gets permits pulled and inspections signed.

We’re an independent contractor and not affiliated with CGI. When your CGI paver system or driveway finish needs a part matched or a section rebuilt, we source the right piece and install it correctly.
Which CGI Models This Applies To
CGI covers a wide spread – interlocking concrete pavers, permeable driveway systems, edge restraints, polymeric joint sand, and the concrete or asphalt base layers they sit on. Matching a replacement part means identifying three things: the paver series, the nominal thickness, and the joint spacing. Most CGI pavers are 60mm or 80mm thick. A 60mm paver in a residential drive is common, but Santa Clarita’s summer heat and the heavy truck traffic on some of our streets push many owners toward the 80mm series for load-bearing drives.
The fastest way to identify your part is to pull a loose paver from an edge and look at the underside stamp, or measure the thickness with a tape. Look at the label on the original pallet if you kept it, or snap a photo of the joint pattern so we can match the profile. The OEM-versus-aftermarket call is simpler than it sounds: CGI doesn’t manufacture everything it brands, so a quality aftermarket paver or restraint with the same dimensions and compression rating will match visually and last the same. What matters more than the brand stamp is the base prep and the joint sand – those two things fail before the paver itself does.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Driveway & Pavers Is Failing
- Paver heave or rocking. This usually means the base didn’t compact to depth. In Santa Clarita, our clay-heavy soils and dry summers create shrink-swell movement that lifts individual units. If a paver rocks when you step on it, the bedding layer underneath has failed.
- Sunken sections or birdbaths. Water that pools after rain means the subgrade has settled. This often happens where the original installer skipped a proper aggregate base and laid pavers too close to the soil.
- Widening joint lines and sand loss. When polymeric sand washes out, joint gaps open and weeds move in. That’s a sign the drainage slope is off, so water is running across the surface instead of shedding off it.
- Hairline cracks across a slab section. On a concrete driveway, cracking follows a control joint problem or a thin pour. Santa Clarita’s afternoon heat and morning cool-down cycles put real stress on a slab that wasn’t cured right.
- Chipped or spalled paver faces. Repeated freeze-free but hot, dry cycling and occasional hard rains can pit a low-grade paver. Spalling usually points to a moisture-retention problem in the base, not just a bad paver.
One honest safety note: paver and slab work isn’t like opening an electrical panel or cutting a garage spring. But a loose paver on a sloped drive is a real trip hazard, and lifting a full pallet of 80mm units by hand can wreck your back. Repairs near the garage apron or on any section holding a parked vehicle are worth having a crew handle.
Replacement Cost & What’s Included
Here’s how the pricing breaks down for Santa Clarita homes:
| Job | Installed Range |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Concrete driveway installation | $4,500 – $12,000 |
| Asphalt driveway paving | $3,500 – $9,000 |
| Driveway replacement (full tear-out) | $5,000 – $14,000 |
| Driveway sealing | $250 – $700 |
| Paver patio installation | $3,500 – $11,000 |
The range swings on square footage, base depth, whether the old surface has to be hauled off, and drainage. A partial paver repair is usually far less than a full drive. Every quote we give lists parts and labor separately, so you can see exactly where the money goes. Your parts and the install are covered under our written 90-Day Done Right Promise – if something’s off, one call brings Tom back.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely handle a few things yourself: pull a loose paver to read the stamp and measure thickness, snap photos of the joint pattern, sweep sand back into joints, and check whether water runs toward or away from the garage. That’s diagnosis, not repair.
Where DIY goes wrong: base compaction. A hand tamper won’t get an aggregate base to the density a driveway needs, and a base that’s 90% right fails in a couple of seasons. Resetting a paver on loose sand looks fine for a month, then it rocks again. And a concrete section poured without proper thickness or control joints cracks through the Santa Clarita heat. If you’ve got a persistent crack, a sunken section, or a heave that keeps coming back, this is a crew job. Call us for a free estimate before you buy material twice.
FAQs
A properly installed CGI paver driveway lasts 25 to 30 years on a well-compacted base, and the pavers themselves often outlast the base. The base and joint sand are what need attention first – expect to top up polymeric sand every few years, and reseal a concrete or asphalt drive every 2 to 4 years given our dry, sunny summers. Call us for an honest read on your specific drive.
Yes – a single chipped or heaved paver can often be lifted and reset, or swapped for a matching unit, without touching the rest of the drive. If the base under that paver has failed, the repair has to include the base or it won’t hold. We’ll tell you which situation you’re in before you commit.
A single-paver swap is a same-week repair once we have the matching unit. A section repair runs a day or two. A full paver driveway install is typically several days depending on square footage and tear-out. We schedule around your parking needs and give you the timeline in writing.
We match on dimensions, thickness, and finish, not on guesswork. You send us the underside stamp or a measured paver, and we source the matching series or a quality aftermarket equivalent with the same compression rating and profile. No mystery brands off a van – the part you get is one you can look up.
Get a Written Estimate on Your Santa Clarita Driveway
If your CGI driveway or paver section is failing, we can give you a straight answer and a written line-item quote. We also install premium hardscape brands like Belgard and Techo-Bloc, and we service KraftMaid, Cambria, and Silestone cabinetry and stone work when your remodel touches the exterior. Our crew members are background-checked and carry the Barrett & Sons name. Standing offers include $40 Off Any Repair Over $200, a Free Second Opinion on Any Written Estimate, No Trip Charge Inside the County, and a permanent 10% Senior & Veteran discount. Call (833) 762-8116 for a free estimate – a live person answers, day or night.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.