Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Roofing: The Santa Clarita Owner’s Guide
ES Windows roof-related components, including flashing kits, termination bars and sealant systems made to pair with ES Windows’ vinyl window and door lines, typically run $400-$1,800 installed as part of a roof repair in Santa Clarita. Most of the parts we see fail are tied to roof penetrations where original ES flashing was removed and never replaced correctly, and those jobs are usually scheduled within a few days once we’ve seen the roof. We don’t keep ES parts on hand, so the real speed question is sourcing, not driving.

Owners in Santa Clarita usually discover the problem the same way: a stain spreading on the ceiling under a window head, a strip of caulk that won’t stay put through a second summer, or a roofer up on the ladder pointing at a gap where the original flashing used to sit. One Canyon Country homeowner we worked with had a foam sealant job from a previous repair that had cracked into three pieces by August – the water had been finding its way behind the ES window frame for two seasons. That’s the pattern we see over and over in Santa Clarita: not a part that suddenly breaks, but a part that quietly stops sealing after the UV and heat have done their work. The fix is usually straightforward once the right piece is matched to the ES model.
Which ES Windows Models This Applies To
ES Windows has made a range of vinyl window and door lines under a few different series names over the years, and the parts we get called about – head flashing, sill pans, jamb trim, and the sealant used at the frame-to-roof transition – are not interchangeable across lines. On most ES units we’ve seen, the model and series information is stamped on the window label inside the jamb, on the frame itself near the sill, or in some cases on a sticker the installer placed in the upper sash channel. If the sticker’s gone, we take measurements of the rough opening and the frame profile, and we use the age of the unit (roughly, from the house’s permit history) to narrow down which ES series it likely came from.
Here’s the decision most owners in Santa Clarita actually face. The OEM ES part is exact-fit, which matters on a vinyl frame with a specific profile, and it’s what we recommend when the original is available. The aftermarket equivalents – GAF and CertainSided flashing accessories, or a local fabricator’s custom piece – can work well, especially when the OEM piece is discontinued or has a lead time. What we won’t do is slide a generic one-size piece into a spot that needs an ES-specific profile and call it done. If you’ve got an ES Window installed under a tile roof, that head flashing piece has to match the profile of the tile, and that’s a fitment question we resolve before we quote – not after we’re up there. We also service KraftMaid, Cambria and Silestone products in the same homes, so if the ES work is part of a larger project, we can look at all of it in one visit.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ES Windows Roofing Is Failing
You don’t need to get on the roof to know something’s wrong. These are the signals we tell homeowners to watch for, and what each one usually means:
- Ceiling stains or damp drywall directly below a window head. That’s water getting past the head flashing, usually because the caulk has failed or the flashing was never properly lapped. In Santa Clarita’s summer heat, standard sealant has a shorter life than the trees around here would suggest – we see failures in three to five years.
- Visible gaps between the window frame and the roof surface. That’s a missing piece of the ES flashing assembly, or one that’s been moved by roof movement or a careless repair. Walk the interior and check the ceiling first; if you see a gap from inside, stop and call.
- Peeling paint or soft trim around the window exterior. This is the classic sign that water’s been coming in behind the frame for a while. Soft wood or a rusted trim band means the flashing has already been letting water in.
- Cracks in the caulk line that reappear within a season. A crack that comes back after resealing usually means the joint is moving, not just drying out. In that case the part underneath needs to be looked at, not just re-caulked.
- Musty smell or peeling ceiling paint in a window-adjacent room. This is what long-term moisture looks like from inside. It’s the symptom we take most seriously, because it’s a sign the roof assembly around the ES window has already absorbed water.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a single ES window-related roofing component – head flashing, sill pan, or the sealant assembly at a roof penetration – we’re typically in the $400-$1,800 range for the repair when it’s a straightforward re-flash and seal. That’s our standard Roof Repair pricing for Santa Clarita, and it covers the part, the labor, and the check of the surrounding roof surface. If the job turns out to be a larger section of the roof around the window, or if there’s rot to repair under the flashing, that extends the scope and the price moves – and it moves in writing, on a change order, before we touch anything.
If the ES window work is part of a full roof replacement, that’s a different scale – most full re-roofs in Santa Clarita run $8,000-$20,000 depending on size, pitch and material, and metal runs $15,000-$40,000. Tile roof repairs specifically, which is common in this area, usually fall in the $600-$2,500 range. Every eligible job gets its permits pulled and inspections signed, and the finished work is covered by our written 90-Day Done Right Promise. If something’s not right, you call Tom and he comes back and makes it right. We’re not affiliated with ES Windows – we’re an independent Santa Clarita service provider – so we quote the part and labor honestly based on what’s actually on your roof.

DIY or Call Us?
Here’s the honest split. You can safely check the ceiling below the window for stains, run your hand along the interior trim for soft spots, and take a photo of the ES window label so we can start matching the part before we arrive. Those are useful things, and they save time.
What we don’t recommend is getting on the roof to handle the flashing or sealant yourself. This isn’t a scare tactic – it’s a fall risk and a leak risk, and stepping onto a pitched roof in Santa Clarita’s dry heat on a hot afternoon is how people get hurt. Beyond that, the flashing has to be lapped in a specific order and the sealant has to sit in a specific way or it fails within a season. That’s not a homeowner’s job, and it’s the kind of repair our technicians (up to 28 years of experience) do on this exact profile regularly.
If you’re seeing any of the signs above, call Barrett & Sons Construction Santa Clarita at (833) 762-8116. We’ll come look at it, tell you what we see, and give you a written quote with the part, the labor and the scope spelled out.
FAQs
Expect five to seven years in this climate before the sealant at a roof penetration needs attention, and ten to twelve years for the metal flashing itself if it was installed correctly. Santa Clarita’s summer heat and dry air accelerate the wear on sealant faster than in coastal areas, so we recommend checking the joint every couple of years. If you’re not sure of the age of the install, call us and we’ll take a look – estimates are free.
Sometimes, yes. If the metal is intact and the only failure is the sealant, a re-seal is often enough and runs less than a full replacement. If the flashing has corroded, been bent, or was the wrong profile to begin with, replacement is the right call. We’ll tell you which one you need after we’ve seen it, and we won’t sell you a replacement you don’t need.
A single window flashing swap is typically a half-day job once we have the right part. The variable is sourcing – we don’t stock ES parts, so if the piece has to be ordered, add a few days to a week. We’ll give you the real timeline up front, not a guess.
We identify the model and series from the window label or frame measurements, then order the OEM piece if it’s available or have the correct-profile aftermarket piece fabricated if it’s not. You’ll see the part cost in writing in the estimate, and the scope of what’s covered before we start. Call (833) 762-8116 to schedule a free estimate.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.