Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Master Halco Home Additions & ADU: The Santa Clarita Owner’s Guide
We build and finish home additions and ADUs in Santa Clarita that tie into Master Halco fencing, railing, and gate hardware already on the property, and the installed ticket usually lands between $45,000 and $130,000 depending on square footage, foundation, and how much of the existing structure we tie into. If you’re adding a pool fence around a new ADU or a matching gate run to close off an addition, the metal hardware is often the first thing that lets go. Most Santa Clarita owners find out the hard way: a gate latch that won’t catch, a post cap rattling loose in the wind, a hinge pin that walks out on its own. That’s usually when the phone call happens. We’re an independent contractor and not affiliated with Master Halco, but we know their parts, their tolerances, and where they fail in our heat and dust.

Key Takeaways
- Master Halco fencing and gate hardware tied to a new addition or ADU typically fails at the latch, hinge, or post cap long before the panels do.
- Most replacements in Santa Clarita run from a few hundred dollars for hardware up to full addition pricing when the structure itself has to be rebuilt.
- Inland Empire heat and Santa Clarita’s dry summers are hard on coated hardware and powder finishes.
- We pull permits and sign inspections on every eligible addition and ADU job.
- Written change orders before any scope change, every time.
Which Master Halco Models This Applies To
Master Halco makes a wide spread of fence, gate, and railing hardware: post caps, hinge sets, latches, gate closers, and the ornamental lines that share a lot of interchangeable parts. The key is matching the part to the series, not just the finish. A latch that fits the Estate and Classic ornamental lines won’t necessarily sit right on a heavier commercial-duty gate, and the hinge kits differ in pin diameter and plate thickness.
How to identify what you have. Start with the gate post itself. Look for a stamped mark or a manufacturer sticker down near the bottom hinge, usually within six inches of grade. If the sticker’s faded, measure the hinge plate and the pin diameter with a caliper or a good ruler, and measure the gate opening. That’s the number the parts house needs. Take a photo of the hinge and latch in place with a tape measure across them in frame, and you’ve solved 90% of the matching guesswork.
OEM versus quality aftermarket: for cosmetic pieces like post caps and finials, an aftermarket match in the same finish is often indistinguishable once installed and saves you money. For latches and hinges on a gate you use daily, we lean OEM or to a known-equivalent brand because the pin tolerance and latch throw matter. A loose latch rattles, then fails, then the gate swings and you’ve got a bigger problem than the latch.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Master Halco Home Additions & ADU Is Failing
- Gate latch won’t seat or pops open on its own. Usually a worn latch tongue or a hinge that’s drifted out of square. Once one hinge sags, the latch has nothing to catch.
- Rattling or squealing hinge pins. The pin has worn the barrel or the plate screws have backed out. In Santa Clarita’s dry heat, wood posts shrink and screws lose grip faster than people expect.
- Powder coat flaking or rust bleeding from the hardware. UV and dust do real damage here. Once the coating breaks, the steel underneath starts to pit.
- Post caps loose or missing. Wind and thermal cycling pop them off. Losing a cap on a wood post invites water down into the grain.
- Gate drags on the ground or won’t swing clean. A hinge has failed or the post has shifted. On additions we tie into existing fence runs, this is the most common call we get.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Master Halco hardware replacement is a modest job. Hinge sets, latches, and post caps typically land in the low hundreds installed; if the gate needs re-hanging or the post is compromised, expect more. When the hardware failure is paired with the addition or ADU itself needing work, we’re in different territory:
| Work | Typical Santa Clarita Range |
|---|---|
| Gate hardware replacement (latch, hinges, caps) | $200 – $900 |
| Full fence run reset or post replacement | $3,500 – $11,000 |
| Home Addition | $45,000 – $130,000 |
| ADU Construction | $90,000 – $220,000 |
| Garage Conversion | $30,000 – $80,000 |
What drives the addition or ADU number: foundation type, whether we’re tying into an existing roofline, electrical and plumbing runs, and finish level. The parts line is parts plus labor, stated separately so you can see what you’re paying for. Every completed job is backed by our written 90-Day Done Right Promise.
DIY or Call Us?
A post cap, a finial, or a gate latch swap is a reasonable Saturday project if you’ve got the right part in hand and a screwdriver. Check the gate swing first, take your measurements, and match the part. Where DIY goes wrong: re-hanging a gate that’s sagged. People shim the hinge, the gate swings worse, and now the post is compromised. On an addition or ADU tie-in, chasing the hardware problem into the structure is where it gets expensive.
A word on safety. The structural connections on an addition, and any electrical or gas tie-in, are not DIY territory. Do the cosmetic parts yourself. Call us for the load-bearing and code work. Our crew members have up to 28 years of experience, and every eligible job gets permits pulled and inspections signed. Call (833) 762-8116 to schedule a free estimate.
FAQs
Expect five to seven years out of a well-maintained latch and hinge set, less on a heavy-use gate in full afternoon sun. Powder finishes fade and pit faster in our heat than in coastal climates, so a hardware check every couple of years saves you a bigger repair.
Often, yes. A latch that won’t seat can sometimes be adjusted rather than replaced, and a loose hinge plate can be re-set with longer screws into good wood. We’ll tell you honestly which it is after we look at it. Call (833) 762-8116 for a free estimate.
A latch and hinge set swap is usually a one-visit job, an hour or two on-site. A gate re-hang or post replacement runs longer. We give you the timeframe in writing before we start.
We match the model and series, then pull OEM or a known quality equivalent from suppliers we’ve worked with for years. You see the part spec and price on the estimate before we order. If it’s a cosmetic piece, we’ll show you the aftermarket match and the savings.
We also handle KraftMaid, Cambria, and Silestone work on additions and ADUs, plus kitchens, baths, roofing, windows, and fences across Santa Clarita. Every scope, allowance, and price change is in writing before work happens. Call (833) 762-8116 for a free estimate, and ask about the 10% Senior & Veteran discount.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.