Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CertainTeed Kitchen Remodeling: The Santa Clarita Owner’s Guide
If you’re searching for CertainTeed kitchen remodeling in Santa Clarita, you’ve probably got a CertainTeed material in your kitchen that’s worn out, and you need it matched and replaced without tearing the room apart. We install and repair CertainTeed-backed kitchen components here in Santa Clarita, and a full kitchen remodel runs $14,000 to $45,000 installed, with single-part swaps landing far below that depending on scope.

Most Santa Clarita homeowners don’t discover a problem until it’s obvious: backer board behind the tile has gone soft, a membrane has let go under the sink, or a surface has chalked and dulled. This kitchen guide covers which CertainTeed products turn up in local kitchens, how to identify the right replacement, what fails first, and what it costs to swap it out. Barrett & Sons Construction is an independent contractor, not affiliated with CertainTeed.
Which CertainTeed Products and Lines This Applies To
CertainTeed touches kitchens through a few product families you’ll find behind and around tile, cabinetry, and wet areas. Their gypsum and tile backer products (including the GlasRoc line) show up behind backsplashes and wall tile in a lot of Santa Clarita kitchens built or remodeled in the last two decades. Whether you’re matching a scrap behind the tile, a label inside a wall cavity, or the stamp on a backer board edge, the part number is what matters, not the brand name.
Here’s how to identify what you’ve got:
- Pull the label or stamp. CertainTeed backer and gypsum products carry a printed edge stamp or a mill label with thickness (typically 1/4″, 1/2″, or 5/8″) and the series name. Photograph it before demo.
- Measure thickness with a tape, not your eye. A 1/2″ board and a 5/8″ board look identical until you check. Ordering the wrong one throws off tile depth and forces a do-over.
- Note the tile setter’s trowel notch. Your installer needs the board’s true thickness and fastener spec to match the existing substrate.
On the OEM-versus-aftermarket question: for a substrate or membrane part, the failure mode is usually moisture or movement, not the brand label itself. A quality equivalent that meets the same spec can work, but only if thickness, fastener pattern, and joist or stud spacing all match. We walk you through that call in writing before anything gets ordered.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CertainTeed Kitchen Component Is Failing
Kitchen substrate and membrane failures announce themselves quietly at first. These are the symptoms we see most in Santa Clarita:
- Soft spots behind tile or under the sink. Water has gotten past the seal, and the board or membrane has taken on moisture. It feels spongy when you press on the tile face.
- Tile that sounds hollow and shifts underfoot. The bond to the substrate has broken. Movement means the board beneath it has swelled, cracked, or delaminated.
- Grout lines that keep cracking after repointing. Grout cracks in a stable wall are one thing; cracks that return within months mean the substrate is moving beneath.
- Chalky, faded surfaces on finished components. Sun through a south-facing Santa Clarita kitchen window and the dry heat wear surfaces faster than in cooler climates. If it dusts off on your fingertip, the finish is gone.
- Visible water stains or efflorescence at board seams. That white salt bloom at a seam is water migrating through. It’s the last quiet warning before a bigger repair.
Replacement Cost & What’s Included
Cost depends entirely on how much CertainTeed material has to come out and go back in, and whether the surrounding finish goes back with it. For a kitchen remodel in Santa Clarita, the honest range is $14,000 to $45,000 for a full room. Part-specific work is far less: a backsplash install runs $800 to $2,500, countertop install $2,000 to $6,500, and cabinet install $4,000 to $13,000.
| Scope | Installed Range (Santa Clarita) |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: how much demo is required, whether the substrate has to be rebuilt, and whether you’re matching existing tile or replacing the whole run. Parts and labor are itemized on your written estimate, and every price change gets a written change order before work moves. All of it is backed by our written 90-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some of this you can check yourself, and some of it you shouldn’t touch. Safe owner checks: press gently on tile faces for soft spots, look for recurring grout cracks, photograph any board label or stamp, and note where moisture shows up. None of that requires opening a wall.
Where DIY goes wrong is the deep side. Cutting into tile and substrate to reach a failed membrane or board means opening a wall cavity, watching for hidden plumbing and wiring, and rebuilding a moisture-tight assembly to spec. A kitchen wall isn’t just a surface; it’s a system, and a bad rebuild means water finds a new path. That’s the repair you don’t want to redo. So do the safe checks, then call (833) 762-8116 and we’ll give you a free estimate on what the fix actually takes.
FAQs
A properly installed CertainTeed backer assembly in a dry, well-ventilated kitchen can last decades, but in wet zones behind a sink or under a window it’s the seal, not the board, that decides the lifespan. Santa Clarita’s dry heat is easy on dry assemblies and hard on anything the sun hits. When water gets past the seal, the failure clock starts fast.
Sometimes, yes. If the failure is localized and the surrounding substrate is still solid, a spot repair can work. If the board or membrane has swelled or delaminated across a run, replacing that section is the only repair that holds. We tell you which one you’re looking at in the written estimate.
A localized part replacement can be done in a day or two; a full kitchen remodel in Santa Clarita takes weeks depending on the scope. We put the schedule in writing before we start, and if something changes, you get a written change order before the schedule shifts.
We match by the label, stamp, and measured thickness, not by guessing off the brand name. That’s the difference between a part that fits the first time and a return trip. Call (833) 762-8116 for a free estimate on sourcing and installing yours.
Contact Barrett & Sons Construction Santa Clarita
We’re an owner-operated crew serving Santa Clarita and the surrounding communities for over 29 years, founded in 1998, and every eligible kitchen job gets permits pulled and inspections signed. We also work with KraftMaid, Cambria, and Silestone when a kitchen job calls for them. You get a written estimate with allowances and change orders in writing, plus our 90-Day Done Right Promise on the finished work. A live person answers the phone 24/7. Call (833) 762-8116 for your free estimate, or ask about our $40 Off Any Repair Over $200 and our permanent 10% Senior & Veteran discount.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.