Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Kitchen Remodeling: The Santa Clarita Owner’s Guide
Most KraftMaid kitchen problems in Santa Clarita come down to one failed component, not a failed kitchen: a hinge that won’t hold, a drawer slide that grinds, a door that’s warped at the top corner. We install and repair KraftMaid-compatible cabinetry and the surrounding kitchen work, and a full kitchen remodel with new KraftMaid cabinets typically runs $14,000 – $45,000 in Santa Clarita. The part swap itself is usually a same-week appointment once we’ve matched the part to your door style and series. Barrett & Sons Construction is an independent provider, not affiliated with KraftMaid.

Key Takeaways
- KraftMaid hinges, slides and door fronts fail in predictable ways, and the failure points differ by series and door style.
- Installed kitchen remodeling in Santa Clarita runs $14,000 – $45,000; a single cabinet part swap is a fraction of that.
- OEM parts match your door front and finish; quality aftermarket equivalents fit the mounting geometry and cost less.
- Santa Clarita’s dry inland heat and the swing between summer highs and cool canyon nights works on wood and hardware harder than a coastal climate does.
Owners usually notice it the same way. A door starts hanging a quarter inch low and rubs the frame. A drawer closes halfway and pops back out. The soft-close on one cabinet quits, then the one next to it. You tighten the screws, they strip out of the wood, and that’s when you start looking for the part.
Which KraftMaid Models This Applies To
KraftMaid builds its cabinetry across a set of series lines, and the hardware that matters depends on which line you own. The full-access lines give you the widest drawers and the slides that carry the most weight. The standard lines use a different hinge mount and a different drawer box. Two cabinets can look identical from across the kitchen and take completely different slides.
Before we quote anything, we identify the cabinet the same way KraftMaid’s own parts desk does. You’ll find a series label inside the cabinet on the back wall or the inside of a side panel, sometimes on a door-back sticker. Failing that, we measure the door height and width and the hinge cup bore. That bore is the number that matters. KraftMaid’s hinge pattern isn’t universal, so a $6 hardware-store hinge will often physically bolt to the door and then bind because the cup depth or overlay is off by a couple of millimeters. We’ve swapped out plenty of those.
The OEM-versus-aftermarket call depends on what failed. A hinge or slide? A quality aftermarket equivalent from a known hardware maker will fit the mounting geometry and outlast the original in many cases. A door front, a finished end panel, or a drawer box with the factory finish? OEM is the honest answer, because aftermarket won’t match the sheen on eleven-year-old maple or the exact glaze on a painted finish. We quote both and let you decide.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Kitchen Remodeling Is Failing
These are the five failures we see most in Santa Clarita kitchens, and what’s actually happening underneath each one.
- The door sags and won’t stay adjusted. The hinge screws have stripped out of the cabinet stile, which is a thinner piece of material than most people expect. Tightening again makes it worse; the holes need filling and re-drilling, or the hinge needs relocating.
- The drawer comes out crooked or jams halfway. One side of the slide has lost its roller or the box has racked a fraction of an inch. KraftMaid drawer boxes in different lines carry different slides, so the matching replacement matters.
- The soft-close has gone silent and the door slams. The damper inside the hinge body wears out long before the hinge arms do. On most KraftMaid hinges this is a hinge replacement, not a whole-door tear-down.
- A door face has warped or the finish has lifted at a seam. Our summer heat and the dry canyon air pull moisture out of wood seasonally, and a door with a poor seal at the panel edge will move. This one usually means a new door front, not a repair.
- The toe kick or a finished end panel is separating from the cabinet. Adhesive and fasteners dry out and let go after years of heat cycling, especially on cabinets near a wall oven or a sunny south-facing wall. It’s a reattach and re-seal job, and worth catching before the panel warps.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what kitchen work in Santa Clarita runs, installed, with parts and labor broken out in the written estimate you get before we start.
| Scope | Installed Range in Santa Clarita |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What moves the number: how many doors and drawers are affected, whether the part is OEM or equivalent, whether the cabinet boxes can be saved, and whether you’re replacing doors on existing boxes or building new cabinetry. A full rebuild adds labor for removal and disposal, and it may add permit and inspection work. Every price change on the job is a written change order before anyone touches a saw.
Countertops are where a cabinet job sometimes grows. If you’re replacing cabinets and keeping your Cambria or Silestone counters, that’s a real constraint we plan around. Kohler sinks and faucets come out and go back in with new supply lines while the cabinet is open. All of it sits under our 90-Day Done Right Promise, written on the contract.
DIY or Call Us?
Some of this you can check yourself, and we’d rather you did. Open the cabinet, find the series label, measure the door height and width, and look at the hinge cup with a flashlight. Take a photo of the hinge and the label. That’s ten minutes and it makes the estimate accurate the first time.
Where DIY goes wrong: replacing a hinge or slide on a cabinet with a warped door, or trying to match a discontinued finish from a big-box shelf. The part fits, the door still rubs, and you’ve spent a Saturday. Cabinet installation isn’t dangerous the way an electrical panel is, but a wall cabinet attached to the wrong framing will pull out, and that’s a loaded cabinet coming down. Two of us with the right fasteners do it in an afternoon.
Call (833) 762-8116 and we’ll schedule a free estimate. Ask for the second opinion on any written estimate you already have. It costs nothing to compare.
FAQs
Expect eight to fifteen years from the original hardware, and less on cabinets by a wall oven or a sun-baked south wall. Our heat cycling is the reason. Santa Clarita summers pull moisture out of wood and push it back in when the nights cool, and hardware at the mounting screws takes that movement first. Call (833) 762-8116 to have us look at yours.
Sometimes, yes. A stripped screw hole can be filled and re-drilled, and a racked drawer box can be squared, which saves the cost of the part. A hinge with a dead damper or a slide that’s lost its roller can’t be repaired and needs replacing. We tell you which one you’re looking at on the visit.
A single hinge or slide is a short appointment, usually under an hour. A full set of doors, or slides across a bank of drawers, is most of a day. If a door front has to be ordered from OEM, the wait is in the part, not the labor, and we’ll give you the lead time in writing.
We identify your series from the cabinet label and match the hinge bore, overlay and drawer box before ordering. OEM comes through KraftMaid’s parts channel; equivalent hardware comes from known makers whose mounting geometry matches. If a finish is discontinued, we tell you that up front rather than after the order.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.