Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Santa Clarita Owner’s Guide
Schluter-compatible bathroom remodeling in Santa Clarita costs $9,000 – $28,000 installed for a full bath, and most of the work is scheduled a few weeks out once materials are ordered and permits are pulled. What you’re actually replacing first is water infiltration and the substrate behind it, not a single part sitting on a shelf. That’s the piece most homeowners miss when they search for Schluter parts. Schluter is a waterproofing and tile systems brand, not a fixture line, so the “part” that fails on a Schluter bath is human and physical: a Kerdi-Fix bead that pulled loose at a corner, a Kerdi-Band seam that lifted, a preformed shower tray that was set out of level, or a drain flange that wasn’t embedded correctly. Owners in Santa Clarita usually find out the slow way: a hairline crack in the grout that keeps returning, a faint musty smell in the closet behind the shower wall, or a stain on the ceiling of the room below after a long shower.

Key Takeaways
- Schluter products to look for on your existing install: Kerdi-Board, Kerdi-Band, Kerdi-Fix, Kerdi-Line and Kerdi-Shower trays, Ditra-Heat, and the Kerdi-Drain line.
- Full bathroom remodel range: $9,000 – $28,000. Walk-in shower only: $4,500 – $12,000.
- Waterproofing failures are almost always about the substrate and the seam work, not the brand of membrane.
- Rebuilding a bathroom correctly means permits and inspections, and we pull them on every eligible job.
Which Schluter Models This Applies To
Schluter’s shower systems break into a few families, and knowing which one is behind your tile tells us how the repair will go. Kerdi-Board is the cement foam backer panel. Kerdi-Band is the seam tape that bridges panels and corners. Kerdi-Fix is the sealant used at drain flanges, pipe penetrations, and mix-material joints. Kerdi-Shower trays are the pre-sloped foam pans, and the Kerdi-Drain and Kerdi-Line drains get embedded into the tray or bonded membrane. For heated floors there’s Ditra-Heat and its accompanying heating cable. If you can’t read a label because it’s under tile and thin-set, the honest way to identify what you have is to pull up a tile or two during an inspection and read the printed edge of the membrane and the drain flange. The common compatibility gotcha: a Kerdi-Drain flange and a Kerdi-Shower tray have to be matched by size and offset, and Kerdi-Board comes in 1/2-inch and other thicknesses that determine how the drain height and tile layout land. On OEM versus aftermarket, there’s no real aftermarket for these parts. Use Schluter’s own Kerdi-Band, Kerdi-Fix, and drain flanges, and don’t substitute a generic liquid membrane at a seam.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
- Grout cracks that return after every patching. This is almost always movement in the substrate or the Kerdi-Board seam underneath, not a grout problem. Repointing the top hides the symptom for a few months and then it’s back.
- A musty smell in the adjacent closet or room. That’s moisture escaping the shower assembly somewhere the membrane wasn’t sealed or where Kerdi-Band was laid with thin-set that dried too fast. A smell is your early warning; visible mold is later.
- Loose or hollow-sounding shower floor tile. Usually a Kerdi-Shower tray that wasn’t embedded fully or was set over a substrate that flexed. On a foam tray, an air pocket under the pan is the culprit.
- Water weeping at the drain flange. The Kerdi-Drain flange wasn’t bonded with Kerdi-Fix and fleece correctly, so water works under the membrane instead of into the drain. This one is urgent, because the damage is in the framing.
- Milky or lifting areas at the wall-to-pan transition. The Kerdi-Band and corner pieces are pulling loose because the substrate wasn’t primed or because the seam was never properly embedded. Left alone, water reaches the drywall and studs.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Santa Clarita, a full bath remodel using Schluter-compatible waterproofing runs $9,000 – $28,000. A walk-in shower only project typically lands in the $4,500 – $12,000 range, a tub-to-shower conversion runs $3,500 – $10,000, and a straightforward shower replacement is $3,000 – $8,500. What drives the range: whether we’re pulling up tile and replacing a failed membrane versus full tearout of the pan and backer, whether the drain line is cast iron or PVC, the tile you choose, how much heated floor you want, and whether permits and inspections apply. Every line item is on paper before we start, and any change to scope gets a written change order. The parts-plus-labor breakdown is transparent: you see what the Schluter materials cost and what the installation labor is, rather than one bundled number. Every completed job is backed by the written 90-Day Done Right Promise.
DIY or Call Us?
Some of the diagnosis is safe for you to do. Check for grout that stays damp, run your hand around the shower base for soft spots, look for efflorescence on the tile, and confirm the age of the installation from your purchase records. What you should not do yourself is tear up tile to inspect the membrane or attempt a drain flange repair, because the failure modes are hidden, water-damaged framing is common behind these installs, and an incorrectly resealed flange can push water into the framing for another season. On a bath with moisture leaking into the walls, call (833) 762-8116. Barrett & Sons Construction Santa Clarita is an independent service provider, not affiliated with Schluter, and we’ll give you a written estimate and a straight answer about whether a repair or a rebuild is the better call.

FAQs
Properly installed, a Schluter shower assembly should last 20 to 30 years or more, and the failure in Santa Clarita is almost never the membrane itself. It’s the installation: poor seam work, a dry-set band, a tray set out of level, or a poor bond at the drain flange. When those fail early, it’s usually within five years of install and shows up as the symptoms above. Call (833) 762-8116 for an exact quote if you think your shower is in that window; estimates are free.
Sometimes, yes. A single failed corner or drain flange can be opened, cleaned, and re-bonded with Kerdi-Band and Kerdi-Fix if the surrounding membrane is intact and the substrate is dry. If water has been reaching the framing, the repair expands to replacing backer board and a section of the pan. Call (833) 762-8116 to schedule a free estimate, and we’ll tell you which one you actually need rather than guessing.
A drain flange or corner repair can be a 1-day job; a shower rebuild is typically 5 to 10 working days once the permit is pulled and materials are on site. We don’t promise same-day on remodels, and we’d be wary of anyone who does. The tile setting, curing, and waterproofing cure time alone take 2 to 3 days. Call (833) 762-8116 for a written timeline that fits your Schluter materials.
We source Kerdi-Drain flanges, Kerdi-Band, Kerdi-Fix, trays, and Ditra-Heat through Schluter’s distribution network once we confirm your exact model from the existing install. There’s no reliable aftermarket for these, so we buy Schluter’s own. Pricing for each item appears on the written line-item estimate before we order anything. Call (833) 762-8116 to schedule your free estimate.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.