Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Kitchen Remodeling: The Santa Clarita Owner’s Guide
Tiled kitchen work in Santa Clarita using Schluter systems typically lands between $14,000 and $45,000 installed, depending on how much floor, backsplash and counter face is involved; a focused backsplash redo runs $800 to $2,500. When the membrane or trim under a tile field starts to go, you usually notice it as a hollow tap near a sink, a grout line that won’t stay filled, or a loose edge strip at the counter. Schi

Most Santa Clarita owners find out after a small leak shows up at the toe kick or a tile pops loose near the dishwasher. We’re an independent installer and not affiliated with Schluter, and we help you match the right profile, membrane and trim to the failure before we quote a thing.
Which Schluter Models This Applies To
Schluter isn’t one product line. It’s a family of systems, and the right part depends on which one failed. A kitchen floor over a wood subfloor usually uses DITRA or DITRA-HEAT, while a backsplash on drywall generally uses KERDI-BAND and KERDI-FIX rather than a full uncoupling membrane. The tile-to-drywall transition at the ends of a backsplash is trim territory: SCHIENE for straight edges, JOLLY for the outer corner, and QUADEC for a quarter-round look. Each comes in sizes matched to your tile thickness (common ranges are 3/32″ to 1/2″), and getting the size wrong by a sixteenth shows at every joint.
The compatibility gotcha most people hit: the profile number on the label (SCHIENE 100, for example) refers to the visible width and the leg length, not the tile thickness. Measure the tile itself with calipers, not a tape, then pick the profile size that fits the tile. For heated floors, DITRA-HEAT-E membrane requires the matching DITRA-HEAT-E-R thermostat and the correct cable spacing, and swapping in a generic thermostat voids the heat warranty. Genuine Schluter parts come from authorized distributors; aftermarket equivalents exist for some profiles, but the alloy and the fleece backing differ, and on a kitchen floor the backing is where cheap versions fail first.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Kitchen Remodeling Is Failing
These are the symptoms Santa Clarita owners bring us, and what’s usually underneath each one.
- Grout cracking in a line across the kitchen floor: the uncoupling layer is likely losing bond to the subfloor, letting seasonal movement telegraph up through the tile. In our clay-heavy soils, this reads as a straight hairline crack rather than random crazing.
- Tiles popping or sounding hollow near the sink or dishwasher: moisture is getting behind the field, often because KERDI-BAND wasn’t lapped correctly at the seam or the change-of-plane joint was treated as flat.
- A loose or discolored edge profile at the counter: the thin-set under the SCHIENE or JOLLY has failed, or the profile was set against the wrong tile thickness and never fully grabbed. It wiggles when you press it.
- DITRA-HEAT warming unevenly or cutting out: a cable is damaged or the thermostat connection is loose, and it’s usually found after a plumber or appliance installer pulls something across the floor.
- Mildew smell at the toe kick after a dishwasher leak: water has been trapped under the membrane instead of draining to a Schluter KERDI-DRAIN or weep path, and the subfloor is staying wet.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A targeted fix (one profile edge, a small membrane patch, a single DITRA-HEAT cable) usually runs well under the full-remodel figure. Here’s how the Santa Clarita numbers break down for the surrounding work, and we quote line by line in writing before anything is ordered.
| Scope | Installed range in Santa Clarita |
|---|---|
| Kitchen remodel (full, with tile floor and backsplash) | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Backsplash installation (with Schluter trim) | $800 – $2,500 |
| Countertop installation | $2,000 – $6,500 |
| Cabinet installation | $4,000 – $13,000 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: square footage, whether we’re removing failed membrane or tile, cabinet or island moves that change the footprint, and whether a heated floor is going back in. Parts and labor are itemized separately. All applicable work gets permits pulled and inspections signed, and every job carries our written 90-Day Done Right Promise: if it isn’t right, one call brings us back.
DIY or Call Us?
You can safely pop a loose trim piece to see if it’s bonded, take a photo of the Schluter label, and check the DITRA-HEAT thermostat for a tripped breaker before calling anyone. That’s the honest ceiling of the safe checks.
Where DIY goes wrong: peeling up a membrane older than a year to “patch” one seam usually damages the neighboring field, and chasing a hollow spot with a tube of caulk traps moisture instead of fixing it. Sorting out a suspected wet subfloor or an electrical fault in a heated floor is not a homeowner job – that’s the same rule that keeps a smart person from pulling live wiring. If the tap-test turns up soft spots or the heat’s misbehaving, call us before you crack more tiles. Call (833) 762-8116 and we’ll schedule a free estimate.
FAQs
A properly installed DITRA or KERDI system lasts 20-plus years in a kitchen, though our hot, dry summers and the seasonal swing between 60°F and 100°F put steady stress on the uncoupling layer that you don’t see in cooler climates. The failure point is usually installation inside the first few years, not age.
Sometimes, yes. A single loose edge profile or a small membrane patch can usually be reset without redoing the whole floor or backsplash. When moisture is trapped under the field or the subfloor is soft, the honest answer is a limited tear-out; we’ll tell you which one you’re facing before you spend.
A trim-profile reset is a few hours; a small membrane patch with cure time is one to two days; a full tile and membrane replacement in a kitchen typically runs 3 to 7 days depending on square footage and drying. We give you the schedule in writing up front, no surprises at the end.
We order genuine Schluter systems through authorized distributors so the profile, membrane and thermostat match the model you have, and we’ll pull the spec sheet first if compatibility is in question. We don’t carry stock on any truck; the right part gets sourced to your job, and the model is confirmed before we cut anything.
If you’re in Santa Clarita and a tile field is lifting, an edge is loose, or a heated floor has gone quiet, we’ll take a look and tell you plainly what it needs. We install Schluter across kitchens alongside KraftMaid, Cambria and Silestone when the project runs that way. Call (833) 762-8116 to schedule your free estimate; a live person answers 24/7, and inside the county there’s no trip charge.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.