Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Fence Installation: The Santa Clarita Owner’s Guide
Unilock fence installation in Santa Clarita typically runs $3,500 to $9,000 for a standard residential run, and the exact number depends on fence height, linear footage, gate count, and whether the property needs footing work in our rocky, fast-draining soils. When we get the call, it’s almost always the same story: a gate that sags and drags, a post that rocks in its footing after a Santa Ana wind event, or a section that leans a few weeks after installation. Those symptoms rarely mean the wall is ruined. They mean one part – a footing, a bracket, a post anchor, a cap, a gate hinge assembly – failed first, and the rest of the fence is paying for it.

- The core question: What failed, and does the Unilock line you have still take that part?
- Typical installed cost: $3,500 – $9,000, quoted in writing before we touch a post.
- Who we are: An independent Santa Clarita fence and construction contractor. Not affiliated with Unilock.
Which Unilock Models This Applies To
Unilock makes modular, dry-stacked fence and wall systems – the kind where molded concrete block columns and infill panels go together with concealed anchors and cap stones. If that sounds like your fence, the part you’re hunting usually falls into one of a handful of categories: the panel-to-column connector, the coping cap adhesive or pin, the steel or polymer post anchor at the base, or the gate hinge and latch kit. The tricky part is that Unilock has revised connector molds and cap profiles across product generations, and a connector that fits one run won’t seat cleanly on another. Before we order anything, we measure the column cross-section and the infill panel thickness and match that against the original spec, not just the general product family.
Here’s how to identify what you have. Look for a faded product label on the inside face of a cap stone or the underside of a base block. Measure the column face width and the panel thickness with a tape, to the sixteenth of an inch. Photograph the failed part next to a ruler. In Santa Clarita we’ve seen more than one fence where a previous installer mixed product generations on the same run, and that’s when the OEM-versus-aftermarket decision gets real: an exact-match replacement keeps the fit, while a “close enough” aftermarket anchor will hold for a season or two and then work loose in our summer heat cycling. We source the correct part from the manufacturer’s current catalog when the spec matches, and we tell you plainly when it doesn’t.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Fence Installation Is Failing
Most Unilock fence failures start small and hide behind a clean-looking surface. Here’s what to watch for:
- A gate that sags or drags on the ground. The hinge anchor has loosened in the column or the post footing has shifted, and the gate is now fighting gravity every time it swings.
- A column that rocks when you lean on it. The base anchor or footing has failed. In our clay-heavy Santa Clarita soils, seasonal wet-dry movement works a loose anchor free faster than most homeowners expect.
- Step cracks at the base of a column or along a cap joint. Moisture has gotten into a hairline gap, and the freeze-thaw and heat cycling we get here opens it further each year.
- A lean that appeared after a wind event. The infill panel anchors have loosened, and one section is now carrying load it was never designed to carry alone.
- Caps that lift or slide. The adhesive or pin holding the coping has failed, and water is pooling under the cap, which is the fastest route to a bigger repair.
Each of these is a single-part failure with a specific fix. The mistake is patching the visible symptom – shimming the gate, propping the column – and leaving the failed anchor in place. That buys you a month and costs you a bigger repair later. Call (833) 762-8116 and we’ll tell you what we’d check first.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a standard residential Unilock-compatible fence install or major repair in Santa Clarita, expect $3,500 to $9,000 installed. A single failed anchor, cap, or hinge kit swapped out runs far less; a full fence rebuild lands at the top of the range. Here’s what moves the number:
- Linear footage and fence height. The single biggest driver.
- Column count and footing work. More columns means more footings, and rocky ground means more digging time.
- Gate and hardware. A custom-width gate and hardware kit adds labor and material.
- Part availability. An in-catalog OEM part is straightforward; a discontinued generation needs a matched substitute.
Every scope and price change comes to you as a written change order before work starts. Permits are pulled and inspections signed on any eligible job – the fence you’re paying a licensed contractor for should be the fence the inspector signs off on. And every completed job is backed by our written 90-Day Done Right Promise: if something isn’t right, one call brings us back. (833) 762-8116 for a free estimate.
DIY or Call Us?
Some checks are safe to do yourself. Measure the part, photograph the label, note the column width, and confirm the fence wasn’t damaged by a root or a vehicle. What’s not safe is pulling a seated anchor or resetting a column footing by hand – a heavy column stone tipping the wrong way is a real injury risk, and a footing packed loose will fail again the first hot spell. That’s where the money got burned. Our technicians have up to 28 years of experience and know exactly which part has to come out and in what order. Call (833) 762-8116 and we’ll take a look before you buy the wrong part twice.
FAQs
A properly installed Unilock-compatible fence should hold for 20 to 30 years, but the anchors, footings, and cap adhesive fail long before the block does – usually in the 8 to 15 year range. The Santa Clarita heat cycling is the main reason: our summers and dry-wet swings work the anchor points harder than mild coastal climates. Call (833) 762-8116 for an exact assessment.
Yes, most single-part failures can be repaired in place – a loosened anchor, a failed hinge kit, or a lifted cap usually doesn’t require tearing out the run. If a column footing or multiple panel anchors have failed, a partial rebuild is more honest than a patch. Call (833) 762-8116 for an exact quote; estimates are free.
A single-part match-and-install typically takes a few hours to half a day, depending on the part and access. A gate hinge kit or a cap replacement is a same-visit job; a column footing reset is a full-day job because the concrete has to set. We’ll tell you the timeline in writing before we start. Call (833) 762-8116 to schedule your free estimate.
We source from the manufacturer’s current catalog using the measurements and label we take at your fence, never a guess from a photo. We don’t carry parts on a truck or keep inventory, so the correct part is ordered to your fence’s spec and confirmed before we arrive for the install. Call (833) 762-8116 and we’ll walk you through what we need to order.
Written by the team at Barrett & Sons Construction Santa Clarita, serving Santa Clarita and nearby areas.